Chain w connector Link-2836,2840,2848

Chain w/connector Link-2836,2840,2848



Chain w/connector Link-2836,2840,2848
Chain w/connector Link-2836,2840,2848 for CUDA Part Washers

Chain w/Connector Link for CUDA 2836, 2840 & 2848 Series Parts Washers

The Chain w/Connector Link is the drive chain used in the turntable drive of CUDA 2836, 2840 and 2848 series front-load parts washers. It carries the drive from the turntable gearmotor to the turntable, so the basket rotates through the spray zone during the wash cycle. The connector link joins the two ends of the chain into a continuous loop.

HPI Processes, Inc. supplies this chain as a replacement part for CUDA parts washers and confirms it against your machine's model before you order.

What the Drive Chain Does

In a CUDA front-load washer, the turntable gearmotor supplies the rotation and the drive chain transmits that motion to the turntable. The chain works with the gearmotor and the turntable's upper and lower bearings as one drive system. Because the chain runs in the wash chamber environment of heated, detergent-based cleaning solution, it is a wear item that should be checked as part of routine maintenance.

Signs the Chain Needs Replacement

  • The turntable does not rotate even though the gearmotor is running.
  • The turntable rotates unevenly, jerks, or hesitates.
  • Noise from the drive area, such as rattling, clicking, or grinding.
  • Visible slack, stretched or stiff links, corrosion, or worn or damaged links.
  • A damaged, bent or missing connector link or retaining clip.
  • Visible wear on the sprocket teeth.

If the gearmotor is running but the turntable is not turning, inspect the drive chain and connector link before replacing the gearmotor. A worn chain can also wear the sprockets it runs on, so inspect the sprockets whenever the chain is replaced.

Installation and Safety

  • Disconnect and lock out power to the washer before servicing the turntable drive. Allow the machine and solution to cool.
  • Check that the turntable is free to turn by hand and that the sprockets are in good condition and aligned.
  • Fit and secure the connector link and its clip as the manufacturer specifies, then confirm the chain moves freely and has correct tension before restarting the machine.
  • Service work should be done by qualified personnel using the machine's service manual.

Compatibility and Ordering

This chain is supplied for CUDA 2836, 2840 and 2848 series front-load parts washers. Chain specification can differ between machine models and builds, and the chain for a CUDA 2518 or 2530 is a different part. Send us your model and serial number from the machine's data plate and we will confirm the correct chain before it ships.

HPI Processes is a distributor of CUDA parts washers and replacement parts , so the chain can be ordered together with the turntable gearmotor, turntable bearings, timers, heating elements and seals.Call: 1-888-733-2832 or request a quote.

Frequently Asked Questions

What is the part number for the CUDA 2836, 2840, 2848 chain with connector link?

The part number is 8.712-987.0.

What does the drive chain do on a CUDA parts washer?

It transmits the drive from the turntable gearmotor to the turntable so the basket rotates during the wash cycle.

My turntable is not rotating but the gearmotor runs. Is it the chain?

It can be. A broken, slipped or disconnected chain, or a failed connector link, stops the turntable even though the motor is running. Inspect the chain, connector link and sprockets before replacing the gearmotor.

What is a connector link?

It is the removable link that joins the two ends of the chain into a loop, so the chain can be fitted and replaced without special equipment.

Can I use the chain from a 2518 or 2530 on a 2836, 2840 or 2848?

No. The chain differs by series. Confirm the correct part with us using your model number.

Should I replace the sprockets when I replace the chain?

Inspect them at the same time. A worn chain can wear the sprocket teeth, and worn sprockets shorten the life of a new chain.

Where do I find my CUDA model number?

On the machine's data plate. Include it, with the serial number, in your quote request.

Distributors of